Installation instructions for Jumbo Square Trampoline

The videos on this page are a guide for an overview reference only. Please note, there are slight differences in the assembly process for each size and shape Springfree Trampoline. Please use these videos for an overview, but refer to your manual for concise, model-specific information and instructions.

Overview and Preparation

Step 1: Laying out the trampoline parts

Layout all parts listed as shown.

Tip - Assemble the trampoline on a flat surface

Confirm all components are present. If you are missing any parts, please call your authorized Springfree™ service center. Contact information can be found here.

Step 2: Staging the trampoline frame

 

Lay out the remaining frame parts as shown. The  yellow stickers on the frame sections and leg pieces all face upwards.

If you are missing any parts, please contact Springfree Trampoline here.

Step 3: Fastening the legs to the frame

WARNING - Fasten the legs to the frame with the bolts and nuts provided. Do not over-tighten.

TIP - The frame may appear loose after it is assembled but will become tight and rigid once the mat is installed.

• Fasten the frame sections together with the large bolts and nuts.
• Attach a center post to the middle of each leg section.
• Then, in the order shown in the illustration, from 1 to 8, lift the frame and evenly put the legs into the leg hole on the frame. We recommend that two people work together to complete this step. One person to hold the frame up and horizontal, and the other person to put the legs into the leg hole.
• Fasten each leg to the frame before going to the next leg.

Step 4: Laying out the mat

• Lay out the mat with the yellow stripes facing upwards inside the trampoline frame.
• Make sure the blue and green tags on the mat line up with the blue and green stickers on the frame.

Step 5 - Positioning the net

NOTE - As you install the white mat rods into the mat rod sockets the net will become tight against the frame. Handle the net with care and be sure that it does not get caught or it may tear.

• Find the hole in the net marked with a blue tag and the mat rod socket on the frame marked with a blue sticker.
• Holding the net hole with the blue tag, place the rest of the net inside the frame as shown.
• Orient the net so that the blue tag is facing you and is on the right hand side of the net hole as shown.
• Put a white mat rod through the net hole and into the mat rod socket marked with the blue sticker.
• Working around the frame, insert the remaining white mat rods through the net holes and into the corresponding mat rod socket.
• Be sure that the white mat rods are seated down to the bottom of each mat rod socket.

 

Step 6, 7 & 8 - Installing the mat

WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod.

 

 

TIP - Keep the mat level when you attach the white mat rods. If you are having difficulty installing the white mat rods, try having a second person push on the opposite side of the trampoline.

 

 

 

 

NOTE - Check that the center posts of the leg sections are correctly seated against the trampoline frame. If they are not, adjust them now.

Attach the first twelve white mat rods to the mat in the order shown. Make sure you correctly match the
colored stickers next to the white mat rods with the colored tags on the mat.

 

 

WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod.

NOTE - When you have put the ball end of a white mat rod into a mat rod holder, swivel the mat to ensure the white mat rod is correctly seated.

• Attach the white mat rods to the left and to the right of the six initial starting rods, as shown above with the green and blue squares.
• Then, as shown by the above numbers, continue this sequence, one to the left and one to the right, until all of the white mat rods are attached to the mat.

 

Step 9 & 10 - Raising the net

 

 

WARNING - Do not use the trampoline until it is completely assembled. Failure to follow these instructions may cause rods to break or eject from the trampoline frame.

NOTE - Check that the net is not caught on the trampoline frame or the bolts – if the net catches, it may tear.

• Move around the frame from right to left and carefully slide the net up to the top of the white mat rods.
• Then, carefully pull the net up over the edge of the mat.
• Working around the frame, lift the rest of the net into the center of the mat.

 

 

 

 

WARNING - Treat any loaded rod with caution until you are sure it is properly installed or uninstalled. Keep your face well away from any loaded rod.

• Locate the orange tag along the top edge of the net.
• Slide a horizontal net rod into the pocket at the orange tag. Tuck the end of the rod into the pocket. Once it is fully inserted, check that the rod is centered within the pocket.
• Repeat on the other side of the trampoline.
• Assemble the black net rods as shown.

 

 

 

 

WARNING - Never attempt to remove a black net rod from its net rod pocket or disengage (unlock) the rod sleeve while the black net rod is under tension.

• Insert all of the black net rods into the net rod pockets at the top edge of the net. Push the rod up into the pocket and past the catch. You will feel some resistance as the ball is pushed through.
• Insert the bottom end of the black net rod into the net rod socket on the trampoline frame. You will hear a click when the black net rod is fully seated.